Screw Fit
The Step by Step Guide to Kitchen Fitting
Ok, the first thing to do is to place a level on the floor in a series of places around the area where the units will be fitted. find the lowest point of the room. This is the place where you will start your datum line. Next, measure the height of your units (not including the feet), measure the height of your plinth and add 5mm for clearance. You will now have the height to set your datum line at. Measure from the floor at the lowest point and put a mark on the wall, then draw a level line around the room.
You can now start to mark out your kitchen as per the plans. Remembering to Mark out all clad on end panels (if supplied). Measure 500mm off your datum line; this will give you the bottom line of your wall unit. Then simply measure the height of your wall units and continue. At this stage it is recommended to mark out where you are going to need electrical or plumbing supplies. Please note all integrated appliances will need these supplies inside the nearest unit as electrical plugs and pipe work behind the appliance will often prevent them pushing back into place.
You are now ready to start fitting your base units. If you have one, always fit the corner unit first and work off this unit as a point of reference. The neatest tool to use for cutting out holes in base units is the hole saw, select the correct size for the cut out in question whether it is for pipe work or electric cables. When leaving spaces between units for appliances, a small amount of clearance is required to enable ease of fitting. This is also helpful for future maintenance and servicing of the appliance. Once all your base units are fitted its time to fit the wall units. Please refer to your instructions manual to find the dimensions for fitting wall unit brackets.
Now all your kitchen units are fitted you are ready to start on the worktops. It is recommended to consult a professional when attempting a butt and scribe worktop joint. However if its worktop strips being used it can be quite an easy process. Measure the area requiring a work surface, add on a couple of inches (80mm) put the worktop in place and mark the underside using the end base unit as a guide. Its recommended using a router and a jig to ensure a straight and true line is achieved. Contact adhesive and a brush or spreader is required to stick on edging strips (if working with laminated worktops)
Once the work surfaces are fitted and screwed down you are ready to cut out your sink and hob appliances. Making sure you refer to the fitting instructions for each set of dimensions. Mark the cut outs and cut out using a jig saw. The pipe work should already be in place, making the connections to the sink and hob a straight forward procedure. Ensure a corgi registered gas fitted is on site to make the gas connection on both the hob and oven. (If required)
You are now ready to start fitting the cornice, lighting pelmet and plinth. This also is the time to fit any infill pieces using a colour coded panel. A Chop saw is required to complete this job professionally.
The last task is to fit the doors onto the units. The reason this job is left until the end is due to the potential damage caused by completing the previous tasks. Once all the doors are fitted its time to fit the handles. You should now have a fully working, perfectly fitted kitchen.
About the Author
About Adflyer:
Adflyer is a free classified site where you can search for a new pet, find new furniture or sell your car. Browse through property, ways to make money and holidays aboard. This is the place for free classified advertising in the UK. Find bargains for sale in your local area and advertise free.
http://www.adflyer.co.uk
info@adflyer.co.uk
INTU Pleated Screw Fit - Measure & Install
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $568.80 |
|
|
Carl ZEISS Jena DDR SONNAR 200mm F2.8 MC - RARE M42 Screw + DIGITAL fit Lens $552.24 |
|
|
Carl ZEISS Jena DDR SONNAR 200mm F2.8 MC - electric M42 Screw + DIGITAL fit Lens $530.00 |
|
|
Canon 50mm f/1.4 lens for Leica Screw Mount 50 /1.4 fit Leica M39 LTM #007344 $500.00 |
|
|
Eagle Specialty Prod Connecting Rods ESP 4340 H-Beam Cap Screw Press Fit Pontiac $471.90 |
|
|
ANTIQUE 9CT NATURAL SAPPHIRE EARRINGS / SCREW FIT $458.20 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
Wholesale Bulk Alloy European Charms Jewellery Beads Fit Bracelets Choose styles $316.00 |
|
|
ANTIQUE VICTORIAN PRETTY 9CT GOLD AMETHYST & GARNET FLOWER SCREW FIT EARRINGS $314.42 |
|
|
ANTIQUE VICTORIAN BULLS EYE AGATE & 9CT GOLD SCREW FIT EARRINGS $308.10 |
|
|
Fujinon 50mm 1:1.4 lens M42 screw fit (New lens, in stock - Unused BOXED) $298.62 |
|
|
Scat 7/16" Cap Screw I Beam Rods 5.7" sb Chevy 350 Bushed Fit Connecting sbc $291.99 |
|
|
Eagle Specialty Prod Connecting Rods SIR I-Beam 5.7" L Cap Screw Press Fit Chevy $252.90 |
|
|
Scat 6.0" Cap Screw I Beam Rods sb Chevy 350 Bushed Fit Connecting sbc $236.99 |
|
|
Scat 6.0" Cap Screw I Beam Rods sb Chevy 350 Press Fit Connecting sbc $231.99 |
|
|
30'S VINTAGE 9CT GOLD CHERRY AMBER EARRINGS /SCREW FIT $229.10 |
|
|
Scat 5.7" Cap Screw I Beam Rods sb Chevy 350 Press Fit Connecting sbc $226.99 |
|
|
Swiss Made Horotec Screw Caseback Opener fits Omega $204.20 |
|
|
Canon 50mm f/1.2 fit Leica screw LTM $200.00 |
|
|
Leica Ballhead 1950s Tripod fit large screw for M3 IIIG $198.00 |
|
|
EAGLE SIR RODS/ I-BEAM/ SBC/ PRESS FIT-3/8" SCREW CAP $189.99 |
|
|
New Steering Shaft With Nut & Screw K912411 Fits CA 880 $189.00 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $179.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT OD GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT CMO GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $169.99 |
|
|
ENNA MUNCHEN Tele-Ennalyt 300mm F/5.6 Lens +Pentax Screw M42 Fit T2 Mount $156.42 |
|
|
Greenlee 683 Screw-Type Reel Stand fits Sumner, Current $145.00 |
|
|
Schneider Kreuznach Xenogon 35mm f/2.8 Chrome fit Leica screw mount LTM L39 $143.50 |
|
|
CARL ZEISS JENNA DDR MC.SONNAR. 1:3.5.f = 135mm.A/M. SCREW FIT.(M42). NEAR MINT. $142.12 |
|
|
07-11 GMC Sierra 1500 Combo Set Billet grille Bolt-on $130.00 |
|
|
07-10 GMC Sierra 1500 Billet Grille Combo Grill 09 2010 $130.00 |
|
|
07-11 GMC Sierra 1500 Combo Set Billet grille Bolt-on $129.99 |
|
|
STRAIGHT ENDED BED RAILS FITS BEDS WITH THUMB SCREW $125.00 |
|
|
07-11 GMC Sierra 1500 Combo Set Billet grille Bolt-on $124.99 |
|
|
PRO-FIT PREMIUM DECK SCREWS STAR HEAD COATED 1-5/8"-3-1/2", 1LB - 25LB $119.99 |
|
|
PRO-FIT PREMIUM DECK SCREWS STAR HEAD COATED 1-5/8"-3-1/2", 1LB - 25LB $119.99 |
|
|
PRO-FIT PREMIUM DECK SCREWS STAR HEAD COATED 1-5/8"-3-1/2", 1LB - 25LB $119.99 |
|
|
PRO-FIT PREMIUM DECK SCREWS STAR HEAD COATED 1-5/8"-3-1/2", 1LB - 25LB $119.99 |
|
|
PRO-FIT PREMIUM DECK SCREWS STAR HEAD COATED 1-5/8"-3-1/2", 1LB - 25LB $119.99 |
|
|
FULL SIZE 1911 TITANIUM FINISH GRIPS COLT GOVERNMENT KIMBER 3-1/16" SCREW FIT $119.99 |
|
|
07-11 GMC Sierra 1500 Combo Set Billet grille Bolt-on $114.99 |
|
|
ANTIQUE MARCASITE EARRINGS / SCREW FIT $118.50 |
|
|
New Leveling Screw Assembly 397095R2 Fits 1026 1206 826 $114.00 |
|
|
New Leveling Screw Assembly 398378R1 Fits 1066 1206 $114.00 |
|
|
Bed Rail Cap WRAP SCREW-ON POLISHED DIRECT FIT SET OF 2 $112.68 |
|
|
New Leveling Screw Assembly 397096R2 Fits 1026 1206 826 $112.00 |
|
|
Mir-1 37mm F2.8 ''Grand Prix BRUSSELS 1958'' M42 Screw + DIGITAL fit RARE Lens! $109.84 |
|
|
Hipshot 6 Screw Stainless Tremolo WIDE Sapcing, fits 2 3/16" FENDER $104.00 |
|
|
Hipshot 6 Screw Stainless Tremolo NARROW Sapcing, fits 2 1/16" FENDER $104.00 |
|
|
SDT 42875 Gear Housing w/ Motor Screws fits RIDGID ® 300 87740 Motor 3177 Rigid $99.99 |
|
|
Leica Visoflex Finder to fit M39 Body screw mount $99.99 |
|
|
07-11 GMC Sierra 1500 Upper Main Billet grille Bolt-on Aluminum Grill Horizontal $99.99 |
|
|
SDT 42875 Gear Housing w/ Motor Screws fits RIDGID ® 300 87740 Motor 3177 Rigid $99.99 |
|
|
03-07 Infiniti G35 Coupe Up + Low Combo Billet grilles $95.00 |
|
|
05-10 Dodge Charger Up Low Combo Replace Billet Grille $95.00 |
|
|
Pentax fit Prinz 200mm f3.5 M42 lens screw mount prime $94.99 |
|
|
05-10 Dodge Charger Up Low Billet Grille Combo 2 Pieces $94.50 |
|
|
New Leveling Screw Assembly 382165R11 Fits 706 & 806 $92.00 |
|
|
07-11 GMC Sierra 1500 Upper Main Billet grille Bolt-on $89.99 |
|
|
03-06 GMC Sierra & HD Up + Low Main Billet Grille Grill $89.99 |
|
|
SDT BC 510 fits RIDGID ® 40205 Heavier Duty Screw Bench Chain Vise Ridgid $89.99 |
|
|
05-10 Dodge Charger Up Low Combo Bolt-on Billet Grille $89.95 |
|
|
Screw Fit Hollow Tunnel with Star CZ and Multi-Gemmed Rim (Pair) $88.90 |
|
|
100pcs Pink Spot Screw Spacer European Charm Beads Fit Bracelet B328 $88.34 |
|
|
100pcs Red Rhinestone Screw Spacer European Charm Beads Fit Bracelet B400 $88.34 |
|
|
RED DOT LASER GRIPS FOR FULL SIZE 1911 FRAME W/3-1/16" SCREW FIT BY GRIPMASTER© $83.00 |
|
|
New Fast Hitch Screw 69831C1 Fits A1 Super A 100 130 $83.00 |
|
|
50pcs, SS Internal Screw Fit Logo Ear Tunnel $81.24 |
|
|
Gasket Door 29" x 24 1/4" fits Randell INGSK290 Mounts with screws 25406 $80.95 |
|
|
250Mixed Plastic Pearl Screw Stopper Fit Charm Bracelet $80.56 |
|
|
FULL SIZE 1911 FIBERGLASS GRIPS FOR COLT GOVERNMENT KIMBER W/3-1/16" SCREW FIT $79.99 |
|
|
SDT BC 510 fits RIDGID ® 40205 Heavier Duty Screw Bench Chain Vise Ridgid $79.99 |
|
|
FULL SIZE 1911 ALUMINUM T6 GRIPS COLT GOVERNMENT KIMBER 3-1/16" SCREW FIT BLUE $79.99 |
|
|
HANDPUNCH WALL MOUNTING PLATE FITS NEW STYLE F SERIES TIME CLOCKS W/SCREWS +KEY $78.88 |
|
|
FULL SIZE 1911 FIBERGLASS GRIPS FOR COLT GOVERNMENT KIMBER W/3-1/16" SCREW FIT $77.99 |
|
|
Aquarium, Vivarium, Domestic 6700k White Colour 21w LED Bulb, E27 Screw Fit $78.98 |
|
|
Screw Fit Hollow Tunnel with Star CZ and Multi-Gemmed Rim (Pair) $76.80 |
|
|
Winchester Swiss Nickel Butt Plate fits Special Single Shot Rifle EC with screws $76.00 |
|
|
Pentax fit Focal 200mm f3.5 M42 lens screw mount prime $75.99 |